alicat

TCP/Serial driver and command line tool for Alicat Laminar DP mass flow controllers.

If you are using Analyt-MTC flow controllers, go to this repository for more info. This driver does not currently support CODA or BASIS controllers.

Example Connections

Installation

pip install alicat

Usage

Command Line

For basic tasks, this driver includes a command-line interface. Read the help for more.

alicat --help

Python

This uses Python ≥3.5's async/await syntax to asynchronously communicate with an Alicat. For example:

import asyncio
from alicat import FlowController

async def get():
    async with FlowController('ip-address:port') as flow_controller:
        print(await flow_controller.get())

asyncio.run(get())
#  If there is already an event loop (e.g. Jupyter), replace the above line with:
#  sawait get()

If the flow controller is communicating on the specified port, this should return a dictionary of the form:

{
  'setpoint': 0.0,         # Setpoint, either mass flow rate or pressure
  'control_point': 'flow', # Either 'flow' or 'pressure'
  'gas': 'Air',            # Can be any option in `flow_controller.gases`
  'mass_flow': 0.0,        # Mass flow (in units specified at time of purchase)
  'pressure': 25.46,       # Pressure (normally in psia)
  'temperature': 23.62,    # Temperature (normally in C)
  'total_flow': 0.0,       # Optional. If totalizer function purchased, will be included
  'volumetric_flow': 0.0   # Volumetric flow (in units specified at time of purchase)
}

On flow controllers, you can set the flow or pressure setpoints.

await flow_controller.set_flow_rate(1.0)
await flow_controller.set_pressure(20)

Gas Type

You can set the gas type by name or by index. For more on setting by index, see the gas table in your Alicat's manual.

await flow_controller.set_gas('N2')
await flow_controller.set_gas(8)

For firmware 5v and greater, you can create and set gas mixes. Mixes can contain up to five gases and are stored in gas indices 236-255.

await flow_controller.create_mix(mix_no=236, name="Mix1", gases={'N2': 50, 'O2': 30, 'CO2': 20})
await flow_controller.set_gas(236)
await flow_controller.delete_mix(236)

PID Parameters

For flow controllers, read and write PID loop settings for device tuning.

await flow_controller.set_pid(p=4000, i=4000, d=10, loop_type='PD2I')
print(await flow_controller.get_pid())
{
    'loop_type': 'PD2I',
    'P': '4000',
    'I': '4000',
    'D': '10',
}

Other Features

Additional features include override commands to increase device functionality.

await flow_controller.lock()            # Lock the front display.
await flow_controller.unlock()          # Unlock the front display.
await flow_controller.hold()            # Hold the valve in its current position.
await flow_controller.cancel_hold()     # Cancel the valve hold.
await flow_controller.tare_volumetric() # Tare volumetric flow.
await flow_controller.tare_pressure()   # Tare pressure.
await flow_controller.reset_totalizer() # Reset totalizer, if totalizer functionality included.

Addressing

You can have multiple controllers on the same port by using Alicat's A-Z addresses and an RS-232 splitter.

flow_controller_1 = FlowController(address='A')
flow_controller_2 = FlowController(address='B')

await flow_controller_1.set_flow_rate(1.0)
await flow_controller_2.set_flow_rate(0.5)

await flow_controller_1.close() # /dev/ttyUSB0 is still open!
await flow_controller_2.close()

Breaking changes

0.5.0

• Support only asyncio. The last version with synchronous code was 0.4.1.
• Rename address/-a to unit/-u to match Alicat's documentation
• Rename -u to -ul (for --unlock)

0.4.1 Remove TCP support. Use pip install alicat==0.3.1 if needed